F.A.Q.
We know that buying a pool cover raises many questions. That’s why we’ve gathered here the answers to the most frequently asked questions about the Coverseal — its installation, maintenance, and much more.
You’ll find them below, organized by topic or accessible through the quick search.
General
- Delete and reinstall the mobile app: Click here for IPhone and here for Android. On first start, allow the use of Bluetooth. The cover can only be connected to one phone at a time.
- Connect close to your cover: If an update is available, the app will guide you step by step. Follow the instructions displayed on the screen. You may need to unplug and then reconnect the power cables. Refer to the provided video if necessary.
- If the “Firmware Installation” or “Cover Check” step loops for more than 2 minutes, follow these steps:
- Close the app completely
- Unplug both black power cables
- Wait 5 seconds
- Reconnect the cables, ensuring they are properly inserted
- Restart the app and repeat step 2
The “Cover check” phase may no longer appear: this is normal. It means the board has restarted correctly. If the update still fails or if the problem persists, contact our technical support.
- Check the power supply: open the side hatch and check that the power connectors (the black cables) are properly seated: from the solar panel (lower cable) and the battery (upper cable). If the cover remains undetectable in the app or if it does not move, proceed to the next step.
- Reinstall the mobile app: reinstall the mobile app: delete it and then install it again. Click here for IPhone and here for Android. When opening for the first time, remember to allow access to Bluetooth. Ensure that only one phone is connected to the cover and finally connect close to it. It is possible that your cover requires an update. In that case, a banner will appear directly in the app. A restart of the board may be necessary; to do this, simply unplug then plug back in the cover’s power cables. Refer to the attached video.
- Test without the solar power supply: unplug the cable from the solar panel (lower black cable). Then try with the wired control or the Open/Close buttons: if the buzzer remains silent, it is probably the fuse (proceed to step 4). If the buzzer sounds but the cover remains still or jerky, it is probably the battery.
- Replace the fuse:
- Fuse version 1: disconnect the two black cables, open the electronic box with a small screwdriver and replace the fuse with the supplied 20A fuse (inside the box). Reconnect, test the cover over 1 m with the buttons or wired control, then reconnect via the app if everything works. Reconnect and test.
- Fuse version 2: open the side hatch and disconnect the two black power cables. First check the battery fuse (at the bottom) and replace it if damaged. Reconnect and test. If the problem persists, check the motor fuse (at the top), replace it, if necessary, then reconnect the cables and restart the application.
If the problem still persists after all these steps, contact your Installer.
Practical questions
Yes, by reducing the intensity of the spray and using a neutral pH soap. Special attention should be paid to rails where regular cleaning is essential to ensure the performance and longevity of your cover. For the trim, we recommend using a microfiber cloth to preserve its appearance and durability.
The membrane that strongly limits photosynthesis and prevents leaves from falling into your pool should keep you from having to resort to shock treatments to purify your pool water. Nevertheless, under exceptional circumstances, this type of treatment may be considered. However, it is strongly recommended to keep the Coverseal open for 24 to 48 hours, to avoid any excessive concentration of chemicals that could damage the membrane.
No. Repeated shocks or excessive pressure may cause deformation of the trim or damage to the mechanics. Such damage is not covered by the warranty.
Yes, on the latest versions of the Automatic model, it is now possible to control your Coverseal from a smartphone while keeping a direct view of the cover when handling it, for safety reasons. The dedicated application also allows you to consult technical parameters such as:
– the charge level of the batteries,
– the number of opening/closing cycles performed,
– the history and details of alarms in the event of malfunction.
For previous versions, an upgrade is possible in order to activate the opening and closing control via your smartphone. We recommend that you contact your Partner directly for more information.
It is not necessary to walk on it to clean the membrane: a low-pressure cleaner (set to moderate power) or a telescopic handle is more than enough. However, you can walk on top of them barefoot or with flat-soled shoes, without any risk.
A quick reminder: the Coverseal provides effective protection in the event of an accidental fall, but it is not designed to be used as a playground.
Our covers do not require any special technical maintenance. However, it is strongly recommended to carry out regular cleaning of the rails and mechanism to remove any accumulation of sand, soil, leaves, branches or other dirt that may affect proper functioning and life of the cover.
In addition, it is necessary to respect the rules stated in the user manual, such as maintaining the appropriate water level in your pool, in order to preserve the safety of the cover.
- Delete and reinstall the mobile app: Click here for IPhone and here for Android. On first start, allow the use of Bluetooth. The cover can only be connected to one phone at a time.
- Connect close to your cover: If an update is available, the app will guide you step by step. Follow the instructions displayed on the screen. You may need to unplug and then reconnect the power cables. Refer to the provided video if necessary.
- If the “Firmware Installation” or “Cover Check” step loops for more than 2 minutes, follow these steps:
- Close the app completely
- Unplug both black power cables
- Wait 5 seconds
- Reconnect the cables, ensuring they are properly inserted
- Restart the app and repeat step 2
The “Cover check” phase may no longer appear: this is normal. It means the board has restarted correctly. If the update still fails or if the problem persists, contact our technical support.
Regardless of the model, your pool cover can always be opened or closed manually. Even in the event of a battery failure, there is always a solution! However, the manual manoeuvre should only be used in the event of a power failure and should not be used to loosen your cover.
1. Remove the 2 flaps (one on each side of the trim). For modules without cylinders, go directly to point 3.
2. Lift the trim on each side until you hear the click.
3. Identify the red motor cable and disconnect it.
4. Identify the manual manoeuvring flange and insert the extension provided during installation.
5. Place the racagnac (ratchet wrench) at the end of the extension, and adjust the knob to the desired position.
You can now operate the system to open or close the cover. To put your cover back in place, reverse the steps from 5 to 1. To lower the trim (only on models equipped with cylinders), actuate the two levers inside it by lifting it slightly before lowering it again.
For the membrane
We recommend cleaning it at least twice a year, depending on the pool’s surroundings (presence of trees, sand, soil, urban pollution, etc.). In any case, a cleaning should be carried out before the first opening and restart of the pool.
The cover must be completely closed and locked before cleaning. Ideally, use a brush and a domestic low-pressure washer, limiting the pressure to 80 bars. The washer should be used with a product that has a neutral pH.
For the cladding
Galvanized steel or aluminum claddings are powder-coated. To clean them, use only a microfiber cloth, clear water, and, if necessary, a neutral pH soap.
For mirror-effect or metallic claddings, monthly cleaning is recommended. Impurities should be removed from top to bottom using a low-pressure water jet. A mild cleaner (without alcohol or ammonia) should be applied with a lint-free microfiber cloth, using linear movements. Circular motions are strictly forbidden, as they may cause streaks or halos. The surface should then be rinsed with clear water and immediately dried with a soft cloth to preserve its shine.
Essential technical maintenance
Regular and careful maintenance of the rails and locking components located under the cladding will extend the lifespan of your cover. Start by removing debris (sand, leaves, branches, soil, etc.) using a vacuum/blower. If necessary, follow up with a water jet, taking care not to push debris into the rail ends.
To clean inside the rails, lift the belt (black strip) when the cover is rolled up (pool open). A high-pressure washer can be used, then reposition the belt correctly after cleaning.
For Automatic models
Regular cleaning of the solar panels helps extend battery life. To do this, use only a microfiber cloth and clear water.
Download the Coverseal app: Click here for IPhone and here for Android.
If you already have an account:
- Check that your phone is properly connected to the internet. Log in with your ID (the email address used during installation) and your password. If you have forgotten your password, click on ‘Forgot password’. You will then receive a 6-digit code by email (wait up to 1 minute). If you do not receive it: check your spam or confirm that the address is correct. If you still receive nothing, contact us!
- Enter your 6-digit code. If the message “Token has expired” appears, you may have requested a new code too soon. If this is the case, wait 2 minutes, delete all emails from noreply@coverseal.com, request a new code and if the problem persists, contact us.
- Lastly, once you have received the code, create a new password (minimum 8 characters, including 1 number and 1 special character).
If you do not yet have an account:
- Your phone must be connected to the internet. You must be invited by an installer or the cover owner. If you are a guest, contact the owner. If you are the owner, contact your Installer.
- The owner can verify if the email address used is correct via: cover details > users
- Check the power supply: open the side hatch and check that the power connectors (the black cables) are properly seated: from the solar panel (lower cable) and the battery (upper cable). If the cover remains undetectable in the app or if it does not move, proceed to the next step.
- Reinstall the mobile app: reinstall the mobile app: delete it and then install it again. Click here for IPhone and here for Android. When opening for the first time, remember to allow access to Bluetooth. Ensure that only one phone is connected to the cover and finally connect close to it. It is possible that your cover requires an update. In that case, a banner will appear directly in the app. A restart of the board may be necessary; to do this, simply unplug then plug back in the cover’s power cables. Refer to the attached video.
- Test without the solar power supply: unplug the cable from the solar panel (lower black cable). Then try with the wired control or the Open/Close buttons: if the buzzer remains silent, it is probably the fuse (proceed to step 4). If the buzzer sounds but the cover remains still or jerky, it is probably the battery.
- Replace the fuse:
- Fuse version 1: disconnect the two black cables, open the electronic box with a small screwdriver and replace the fuse with the supplied 20A fuse (inside the box). Reconnect, test the cover over 1 m with the buttons or wired control, then reconnect via the app if everything works. Reconnect and test.
- Fuse version 2: open the side hatch and disconnect the two black power cables. First check the battery fuse (at the bottom) and replace it if damaged. Reconnect and test. If the problem persists, check the motor fuse (at the top), replace it, if necessary, then reconnect the cables and restart the application.
If the problem still persists after all these steps, contact your Installer.
This makes it possible to guarantee the safety of your loved ones and the good condition of the cover by directly detecting if someone is in the pool or if any obstacles are on the membrane (branches, wipes, ball, etc.).
It is a pre-stressed membrane coated with several layers of polymer, capable of supporting several tons and recovering its initial shape after deformation. It is, therefore, a solution that guarantees safety and tranquillity for the whole family.
On previous generations of Automatic models, the winterization switch allowed you to disable the remote control receiver to preserve the batteries during the low season, when the sunshine is lower. It is recommended to place it in the OFF position from 1 September to 1 May. Otherwise, the batteries could fall into deep discharge and require replacement.
Note: on the latest versions of this model, this switch is no longer present, because energy management has been optimized.
All you need to do is:
– close the cover completely
– maintain the water level of your pool according to the instructions in the user manual;
– clear the solar panel(s) of the Automatic model in case of heavy snowfall to maintain a good charge of the batteries
– set the winterization switch to off in order to preserve the batteries (previous versions of the Automatic model)
Thanks to the membrane, photosynthesis is strongly limited: no noticeable dirt is found in the spring. For optimal results, it is advisable to run the filtration only a few hours a day during wintering.
Request your catalogue
"*" indicates required fields